How Much Does It Cost to Rewire a House in Wollongong?

In Wollongong, a partial rewire costs between $2,500 and $8,000, while a full rewire costs anywhere between $8,000 and $25,000. Most 2- to 3-bedroom single-storey homes will cost between $8,000 and $15,000. Many factors can influence rewiring costs, such as house size, the age of the wiring, and how easily cables can connect to each room. This guide comes from the licensed team at Easther Electrical and explains what drives the price so you can judge your own quote.
These are guide figures; only an on-site inspection can provide you with a firm price.
What’s Involved In The Process of Rewiring a House?
A full rewire replaces the wiring throughout the whole house, while a partial rewire replaces only part of it, such as the circuits for a kitchen, a bathroom, or an extension.

Both jobs involve the same parts:
- The switchboard, which holds the circuit breakers and safety switches (RCDs)
- The cabling in the walls, ceiling and roof space
- Power points
- Light points
The work must legally meet AS/NZS 3000, the Wiring Rules. In NSW, only a licensed electrician can carry out electrical work. When the job is finished, they must give you a Certificate of Compliance for Electrical Work (CCEW).
Average Cost to Rewire a House in Wollongong
Partial Rewire Cost
A partial rewire usually costs between $2,500 and $8,000 and covers one or two rooms or a set of critical circuits, such as a kitchen and bathroom, or the circuits that keep tripping. It suits homes where testing shows the rest of the wiring is sound, and makes sense when you’re renovating one area and the old cabling.
Full Rewire Cost by House Size
| House type | Typical total cost |
| 2 to 3 bedroom, single-storey | $8,000 to $15,000 |
| 4+ bedroom, double-storey or difficult access | $15,000 to $25,000+ |
Where your home lands in each bracket depends on the number of bedrooms, extra living areas, roof and wall access, and whether anyone is living there during the work.
Two items are worth checking on any rewire quote:
- A new switchboard with safety switches often costs from about $700 to $2,000 or more.
- Adding extra power points or light points to the agreed scope costs roughly $65 to $150 each.
These are whole-project prices, not hourly rates.
What’s Usually Included in the Price?
A rewire quote should normally cover:
- Labour
- Materials, such as cable, power points, switches and circuit protection
- A new switchboard with safety switches
- Testing and the compliance certificate
These are often quoted separately or left out:
- Patching and painting. Cabling that’s chased into brick or plaster leaves walls that need repair. Unless a plasterer or painter is part of the quote, that cost is yours.
- Matching cover plates. New plates may not match your existing finishes.
Ask about both before you sign.
What Affects the Cost of Rewiring a House?
Two similar-looking homes can get very different quotes, and the difference usually comes down to the following:
- Age and type of existing wiring. Rubber-insulated (VIR) cable breaks down with age and is a common reason for a rewire quote. You’ll mostly find it in homes wired before about 1960. Some older homes may also have aluminium wiring. If your cabling is plastic-sheathed (TPS) and in good condition, targeted work may be enough. Older suburbs such as Coniston, Gwynneville, Corrimal and West Wollongong have homes where original wiring may still be in place; newer areas such as Shell Cove are less likely to need a rewire.
- Wall and ceiling access. Timber-framed homes, such as weatherboards and brick veneer, usually let cables run through the wall cavities. Solid brick and concrete walls are slower jobs, because cables have to be chased in or routed another way, meaning a tight roof space adds time to every cable run.
- Number of storeys. A double-storey home needs more cable runs between floors and more time working in confined spaces.
- Occupied or vacant. Working around furniture and daily routines means staged access and more time. A vacant home or a gutted renovation is quicker and usually cheaper.
- Switchboard condition. An old fuse board usually gets replaced as part of a rewire. A recent board in good order may stay.
- Bundled work. EV charger prep, solar pre-wiring, data cabling, renovation changes and granny flat circuits all add scope to the works.
Signs Your Wollongong Home Might Need Rewiring

- Safety switches that trip continuously
- Power points or switches that feel warm, look discoloured or have started cracking
- Lights that flicker or dim when an appliance is turned on
- A fuse board instead of circuit breakers
- Rubber- or fabric-insulated cable, or aluminium wiring, in the roof space or switchboard
- A home built before the 1980s that has never been rewired
- A building and pest report that flags the wiring
Worn wiring is a fire risk. It’s also worth asking your insurer how they treat old wiring, as policies can differ.
Do You Need a Partial Rewire or a Full Rewire?
Run through this checklist before you make any decisions.
A partial rewire is likely enough if:
- Problems are limited to one area or a few circuits
- The rest of the house has modern cabling and circuit breakers
- You’re renovating one section, and the remaining wiring tests sound
A full rewire is more likely if:
- The cabling is rubber-insulated, fabric-covered or aluminium
- Faults keep showing up in different parts of the house
- The home has original wiring and a fuse board
- You’re planning a major renovation or extension, or adding EV, solar or smart home loads
Only a licensed electrician can inspect and test to confirm which one you need. This table shows the two.
| Partial rewire | Full rewire | |
| Typical cost | $2,500 to $8,000 | $8,000 to $25,000+ |
| Typical time | 1 to 2 days | 3 days to 2 weeks |
| What’s included | Affected rooms or circuits, testing, compliance certificate | Whole-house cabling, power and light points, new switchboard, testing, compliance certificate |
Time depends on house size and access.
How to Get a Fair, Accurate Rewiring Quote in Wollongong
You can’t price a rewire properly over the phone; keep an eye out for the following.
- A site inspection first. A fixed price needs someone to inspect your switchboard, roof space, and walls.
- An itemised scope. The quote should state how many power points and light points are included, whether the switchboard is new, and what’s left out, such as patching and painting.
- That a compliance certificate is included.
- A licence you can check. Look up the electrician’s licence number on the NSW Government’s online licence check.
- A fixed fee. On a job that runs for days, hourly billing leaves the risk with you. If the roof space is tighter than expected, the bill grows. A fixed fee set after inspection puts that risk on the electrician, and you know the total before work starts.
Frequently Asked Questions
How much does it cost to rewire a 3-bedroom house in Wollongong?
Most 3-bedroom single-storey homes cost about $8,000 to $15,000 to rewire fully. Wall type, roof access, switchboard condition and extra work such as EV charger prep decide where yours lands.
How long does it take to rewire a house?
A partial rewire generally takes 1 to 2 days, whereas a full rewire of a standard home commonly takes 3 days to 2 weeks, depending on size and access; occupied homes can take longer.
Do I need a permit or compliance certificate to rewire my house in NSW?
You need a licensed electrician, and they must give you a CCEW. They also handle the paperwork. For switchboard work, copies go to your energy distributor and NSW Fair Trading.
Can I stay in my house while it’s being rewired?
Usually, yes. Power will be off at times while the work is underway, so plan around it, including how you’ll keep the fridge cold. Staged access is also why occupied homes tend to cost more than vacant ones. Ask your electrician how they’ll stage the work.
How do I know if my house needs a full rewire or just a partial one?
Use the signs and checklist above, then book an inspection. Testing the condition of the existing cabling is the only reliable way to know.
Does rewiring include a new switchboard?
Usually, yes. A switchboard upgrade is normally part of a rewire quote. If your wiring is sound and only the board is outdated, we also offer a standalone switchboard upgrade.
Get a Fixed-Fee Rewiring Quote from Easther Electrical
Easther Electrical is a locally owned and operated, fully licensed residential electrician in Wollongong. We’re affiliated with Master Electricians Australia and NECA, and we work across Wollongong, Dapto, Corrimal, Shellharbour, Kiama, Figtree and nearby suburbs. Once we give you a quote, we stick to it.
Get a fixed-fee rewiring quote. No hidden costs, no surprises. Request your free quote today.
Not sure if you need a full or partial rewire? Talk to our licensed Wollongong electricians on 02 4256 5899, and we’ll assess it for you.
